Top Quality Plastic sucking hooks for bathroom & toilet Iceland Manufacturer

Video tutorial on how to remove the anti shudder valve (asv) on a VW Golf, Jetta, Bora, MK4 TDI PD BEW engine. Some other models that came equipped with a PD100 included some Skoda models, Audi models, and VW Passat. After a while of operation, the anti shudder valve does build up with dirt and debris which does need to be cleaned. Anti shudder valves can also malfunction over time either getting stuck open or closed, therefore not allowing the engine to start. The original function of the unit shudder valve is to prevent a “run-away diesel” and to allow for quieter engine shutdowns. This particular tutorial was done on a 2004 Volkswagen Golf TDI.

Website: https://4diyers.com
Facebook: https://www.facebook.com/4diyers
Google Plus: https://plus.google.com/+4DIYers
Twitter: https://twitter.com/4DIYers
Instagram: https://www.instagram.com/4diyers/
Tumblr: https://4diyers.tumblr.com
Pintrest: https://www.pinterest.com/4diyers/

Tools/Supplies Needed:
-interlocking pliers
-allen wrench

Procedure:
-first remove the engine cover by pulling straight up on the two front corners, once it’s release pull straight towards you
-next remove the boost hose from the plastic tube and then from the anti shudder valve
-remove the clamp on the plastic tube side using the interlocking pliers by squishing the tabs and moving it off the rubber hose
-pull straight out of the anti shudder valve, ensure that you disengage the snap ring
-remove the three allen head bolts, two are visible on top and the other is hidden underneath of the unit
-remove the anti shudder valve from the intake
-disconnect the electrical connector from the anti shudder valve motor unit, there is a tab on the side that needs to be pulled back to disengage it from the clip
-all allen head bolts are the same length
-when reinstalling, ensure the mounting faces are clean
-installation in reverse

Thank you to all those who watch my videos and support my content. Don’t forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!

© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

How to Strip Cable by Marvel Tools Australia

https://www.marveltools.com.au/

MA880 Heavy Duty Linesman’s Pliers

Diamond pattern nose grip for cleaner, sharper edges and better grip.
Radiused chain grip for gripping, pulling, bending and turning.
Precise tip clearance as blades are individually adjusted and checked.
Extra long cutter blades for cutting multi-stranded flat cables with one snip.
Made from drop forged hardened steel and fully heat treated.

https://www.marveltools.com.au/featured/heavy-duty-linesman-s-pliers.html

MA730 High Leverage Cutting Nippers

High leverage design with bevelled blades.
For heavy duty cutting of steel wire.
Made from drop forged chrome vanadium steel.
Fully heat treated, black finish with polished jaws.
Ground head with dipped vinyl handle grips.

https://www.marveltools.com.au/cutters/high-leverage-cutting-nippers.html

MESE2 Wire Stripper Small Diameter Wire 1.6-2mm

Strips small diameter cables in a single movement.
Precision ground special tool steel blades cut cleanly through insulation.
Blades shaped to avoid damage to conductors.
Sturdy die cast alloy body with polyvinyl handle grips.
Ground tool steel jaws and fully heat treated blades.
Locking action prevents jaws snapping back onto stripped cables.

https://www.marveltools.com.au/wire-strippers/wire-stripper-small-diameter-wire-1-6-2mm.html

MES-A Automatic Wire Stripper