OEM manufacturer custom 5-PCS Hex Key Sets packaged by spring ring Gambia Factories

Short Description:

Product Detail

Product Tags

With our rich experience and considerate services, we have been recognized as a reliable supplier for many international buyers for OEM manufacturer custom 5-PCS Hex Key Sets packaged by spring ring Gambia Factories, We are sincere and open. We look forward to your visit and establishing trustworthy and long-term standing relationship.

Basic Information

■Model Number: RL-NLJ001

Additional Information

■Material: 45# Carbon Steel

■Size: 1/16″-3/8″, 1.5mm-10mm

■Surface Treatment: Zinc-plated, Black Oxide

■Heat Treatment: Optional

■Package: Spring Ring + Suction Card

■OEM: Acceptable

■HS Code: 8204110000

■Samples: For FREE

■Delivery Time: Always 30 working days depending on the order quantity

■Packing: By standard cartons

Product Description

■Ningbo Rilong Hardware Tools Factory can provide various kinds of Hex Key with different sizes and packages.

Product Image

Previous:

Next: 5″ Forehand Curved Jaw Locking Pliers

Allan Key

Hex Wrench To Open Door

lineman's pliers

vice grip clamps

Watch the full episode: https://www.youtube.com/watch?v=Y_6Bj6nmo-o

This Old House plumbing and heating expert Richard Trethewey shows how to replace a badly corroded cast-iron flange. (See the shopping list, tools, and steps below.)

Click here to SUBSCRIBE to the official This Old House YouTube channel: https://www.youtube.com/subscription_center?add_user=thisoldhouse

Shopping List for How to Repair a Cast-Iron Toilet Flange:
- Plastic expansion closet flange, to replace old cast-iron flange
- Large sponge and bucket, for sopping up water
- Four wood blocks, used as spacers beneath the new closet flange
- Rubber gasket, for sealing toilet to flange

Tools for How to Repair a Cast-Iron Toilet Flange:
- Wrench, to loosen and tighten hex nuts
- Close-quarter hacksaw, for sawing through bolts
- Stiff-blade putty knife, to scrape off wax gasket
- Screwdriver
- Hammer and cold chisel, for chopping out the cast-iron flange
- Pliers, to pull out the old flange
- Wet/dry vacuum, for collecting dust and debris
- Ratcheting hex-key wrench, to tighten the flange screws

Steps for How to Repair a Cast-Iron Toilet Flange:
1. Close the shut-off valve behind the toilet to stop the flow of water.
2. Remove the lid from the toilet tank. Flush the toilet and hold down the flush lever to drain as much water from the tank as possible.
3. Reach inside the tank and unscrew the ball float.
4. Use a large sponge to sop up the remaining water from inside the tank and from the bottom of the toilet bowl.
5. Remove the nuts from the closet bolts on each side of the toilet base. If the nuts are rusted in place, cut through the bolts with a close-quarter hacksaw.
6. Unscrew the water-supply line from the underside of the toilet tank.
7. Rock the toilet back and forth to break its wax seal with the drainpipe. Lift the toilet and carry it out of the room.
8. Use a stiff-blade putty knife to scrape away the wax gasket from the closet flange.
9. Unscrew and remove any extension rings to expose the cast-iron closet flange.
10. If the flange is badly corroded, use a hammer and cold chisel to chop out the flange.
11. Pull the loosened flange out of the cast-iron drainpipe with a pair of pliers.
12. Vacuum up all dust and debris from around the drainpipe and bathroom floor.
13. Set four wood blocks around the drainpipe to hold the new closet flange at the correct height.
14. Install a plastic expansion closet flange into the cast-iron drainpipe.
15. Use a ratcheting hex-key wrench to tighten the four screws on the inside of the flange until the flange is tightly wedged into the drainpipe.
16. Slide two new closet bolts into the slotted keyways in the flange.
17. Place a rubber toilet gasket over the bolts and onto the closet flange.
18. Set the toilet back into place on top of the gasket.
19. Onto each closet bolt put a plastic washer, stainless-steel washer, and hex nut. Alternately tighten each nut with a wrench, being careful not to crack the toilet base.
20. Trim off the excess bolt with the hacksaw.
21. Snap on the plastic caps to conceal the closet bolts.
22. Reattach the water-supply line to the underside of the toilet tank.
23. Screw the ball float back onto the flush valve.
24. Open the shut-off valve and flush the toilet to ensure it’s working properly.

Follow This Old House and Ask This Old House:
Facebook: https://www.facebook.com/ThisOldHouse
Twitter: https://twitter.com/thisoldhouse

https://twitter.com/asktoh

Pinterest: https://www.pinterest.com/thisoldhouse/
G+: https://plus.google.com/+thisoldhouse/posts
Instagram: https://instagram.com/thisoldhouse
Tumblr: https://thisoldhouse.tumblr.com/

https://www.rockymountainatvmc.com/p/989/20342/Tusk-Bearing-Remover?utm_source=Youtube&utm_medium=WheelBearingReplacement&utm_campaign=Youtubevideos Learn the easy way to replace the old worn out wheel bearings on your motorcycle! In this video we walk you through each step of properly replacing the wheel bearings on a motorcycle. Using the correct tools for the job is key to making it go smoothly and Rocky Mountain ATV/MC carries all the tools and parts to make this job quick and painless. In this video we’ll be demonstrating this process using the Tusk Bearing Remover. Checking to see if your wheel bearings are worn out or bad is simple. Just suspend the tire/ wheel off the ground and pull the tire to each side. If you feel and side to side play or see any movement in the bearings you know it’s time to replace them. Save yourself some money by replacing these bearings yourself! Rocky Mountain ATV/MC has plenty of bearing & seal kit for you to choose from including All Balls, Pivot Works, and Bearing Connections. Pick up your new set of wheel bearings today @ www.rockymountainatvmc.com!