Factory source manufacturing Metal Drain Cleaner packing by cross for Peru Importers

Like Us on Facebook! https://www.facebook.com/DiyForKnuckleheads?ref=hl How to install concrete anchors.How to attach timber / wood to concrete or any other SOLID masonry surface using DynaBolts. DynaBolts are the ideal anchor for attaching almost anything to solid masonry such as concrete. This video will look at attaching timber to a concrete floor.

The Tools You’ll Need Are:

Hearing protection,
Dust Mask.
Goggles.
Bike pump (to remove the concrete dust from inside the hole after you’ve drilled it).
A hammer drill or rotary hammer drill.
A suitable concrete anchor.
A masonry drill bit suitable to the diameter size of your anchor. For example, if the diameter of your masonry bolt is 10mm, you would use a 10mm masonry drill bit.
A hammer, and a
Torque wrench, spanner or socket to tighten the anchor once installed.

The steps to attach timber to concrete using masonry anchors are as follows:

Step 1:
First of all position your timber in place and pre-drill (if necessary) the hole (in the timber) where you want the concrete anchor to go. Personally l don’t pre drill. If you have a rotary hammer drill it is quite capable of drill through timber (pine framing) using a masonry drill bit.

Step 2:
With the timber in place and using your hammer drill or rotary drill, drill the hole in the concrete making sure that depth of the hole is about 10mm deeper than the length of the anchor. This will ensure that the even if there is a little bit of debris left in the bottom of the hole after drilling, the anchor won’t bottom out to early leaving it proud of the surface of the timber. Trust me, you don’t want this to happen. Please be aware that the thickness of concrete on a typical ground floor slab is is only around 100mm or 4 inches unless it is the perimeter of the building which is actually quite thick. You don’t want to drill any deeper than that other wise you will penetrate right through the slab and the plasic barrier beneath the slab which can lead to moisture drawing up through the hole in the plastic and concrete. Anyway, once you’ve drilled to your desired depth, run the drill up and down a few times to help clear the dust out of the hole. Leaving the drill in the hole, dust the dust away from the hole. Once drilled ensure that all the concrete dust is removed from in and around the hole. Using a bike pump is a great way of removing excess dust from the hole.

Step 3:
Insert the anchor into the hole (please be aware that concrete anchors are made in a variety of materials. Some are suitable only for indoor use and others are suitable for indoor and outdoor use. Read the back of the packet for details). You use your hammer at this point to tap the anchor in.
Finally, using your spanner or socket (the correct way is to use a torque wrench but not to many people have these., tighten the nut on top until tight and you’re done!!!!

Bonus Tip: When drilling into concrete, a rotary hammer drill is far more effective tool than the standard hammer drill. They only cost around $60.00. Well worth the investment!

Thanks for watching.
Please sub, thumbs up, add to favourites, comment and share.
Cheers, Uncle Knackers.

Please Note:
All Videos produced by shaneconlan1′s YouTube Channel are provided for informational purposes only.
All the content provided is for general guidance only. Because tools, products, materials, equipment, techniques, building codes and local regulations are constantly changing, shaneconlan1 cannot, and does not assume any responsibility or liability for the accuracy of the information contained therein. Further, shaneconlan1 (Shane Conlan) will not accept any claim for liability related to, but not limited to, omissions, errors, injury, damage or the outcome of any project. It is the responsibility of the viewer to ensure compliance with all applicable laws, rules, codes and regulations for a project. The viewer must always take proper safety precautions and exercise caution when taking on any project. If there are any questions or doubt in regards to the element of a project, please consult with a licensed professional.

In this video Mark explains the steps necessary to remove a drill press spindle. A drill press spindle can become bent if it is placed under too much strain. If this happens, you will need to replace it.

Get a replacement spindle for your drill press here: https://www.ereplacementparts.com/drill-press-parts-c-18715_18731_18747.html

For other power tool replacement parts, visit: https://www.ereplacementparts.com/power-tool-parts.html

To read this video’s repair article, visit: https://www.ereplacementparts.com/article/7076/How_to_Remove_and_Replace_a_Drill_Press_Spindle.html