Best quality and factory Various kinds of Industrial Brushes for Serbia Factory

Removing a belly button ring is only safe after the piercing is completely healed, and it requires unscrewing the ball at one end and sliding the jewelry out carefully. Remove a belly button ring with tips from a licensed piercer in this free video on body modification.

Expert: Tristan McCauley
Contact: www.luckyseventattoo.net
Bio: Tristan McCauley has been piercing for two years after a 9-month apprenticeship under Brian Price, a 12-year veteran in the craft.
Filmmaker: Reel Media LLC

WEBSITE: https://www.swimmingpoollearning.com/

YouTube Video Index — A list of all of my videos: https://poolmandave.blogspot.com/2014/03/swimming-pool-tips-reviews-how-to-video.html

I already had re-plumbed the pump inlet last week so this is how you do the pump discharge line that sits above the pump. You would plumb both the same way.
TO SEE THE NEW VERSION OF THIS REPAIR WITH HIGH HEAT NIPPLE PIPE:
Repairing A Pump Discharge Leak Updated & Revised Version: https://youtu.be/o5V6P0IQpM4

RELATED VIDEOS:
How to Fix Leaking Swimming Pool PVC Pipes: https://youtu.be/07cvZyxJiEU
For Part 1 of Pool Pump not Working see: https://youtu.be/_k-BLL98bFU
For part 2 which covers manually priming your pump: https://youtu.be/oshWO3zq17o
Clogged Impeller, pool pump not priming: https://youtu.be/tdhkddQKb6M
Skimmer Weir stuck, pump not priming: https://youtu.be/iKWJIFcK4MA
Pool Skimmer Weir replacement & Install: https://youtu.be/DTDWA-la33w
Pool motor tips, motor burning out: https://youtu.be/IdpoNzrBV8M
Pool Water Level, proper water level: https://youtu.be/6dXIY0YN7bE
Replacing a Pool Pump Housing Gasket: https://youtu.be/r0ReyYVpVM8
Filter Saver, skimmer inserts: https://youtu.be/p0l-pNoO_eM
Variable Speed Pumps, Dual Speed Pumps, a quick overview: https://youtu.be/YgOq1X65Kvg

NOTES:
This is not a very difficult job, but it does require accurate measurements for the pipes to fit together. The last pipe fitting you do will be the most difficult as that will be the one that will make a complete sealed plumbing. Please plan accordingly so you will be able to fit it on. In this video I was able to move the pump back about 1 inch and slide the last pipe on, then I pushed the pump back completing the plumbing seal. It takes some practice but you can do it. If you make a mistake, simply cut out the pipe or use a new pipe and new fittings. The pipe fittings are not very expensive. All the material for this job will cost you about $20 -$25. Just by extra fittings in case you make an error in your cutting or measuring.

Parts list:
2″ MALE ADAPTER THREADED FITTING (for top of pump)
For a better heat rating you can use this pipe also:
2″ x 12″ nipple cpvc pipe (grey) and rated to 140 degrees
2″ SLIP COUPLING
2″ PVC PIPE 5 FT
2″ SLIP 90 DEGREE ELBOWS
2″ FITTING EXTENDER
POOL-TITE GLUE .5PT
Plasto-Joint Stick Thread Sealant 1.25oz 11775 for threaded fitting on top of pump
You can also use plumbers tape

Of course if your pool has 1 ½” pipes adjust the fitting size accordingly.

Pool-Tite Glue Instructions:
Shake can well. Use a primer to clean the pipe fittings (priming step is not needed for non-pressure pipes less than 4″ in diameter. Apply liberal coat of cement to pipe depth of the socket, leave no uncoated surface. Apply a thin coat inside if the fitting, avoid puddling, Apply a second coat to the pipe. Assemble parts Quickly. Cement must be fluid. If cement surface has dried recoat both parts. Push pipe firmly into fitting giving it a ¼ turning motion. Hold pipe and fitting together for 30 seconds to avoid it popping out. Glue can get old so if it is gel like don’t use it.

You can use the Purple primer or the clear one to prep the pipes. The Purple primer has a very strong dye in it so if you drip it won’t come off, so the clear one is less messy.

Sometimes the pump itself will have warped a bit from the heat. In that case the 2″ x 12″ nipple cpvc pipe will sometimes seal it better.

Here is a look at the pipe online -

https://www.grainger.com/Grainger/GF-PIPING-SYSTEMS-Pipe-Nipple-6MW40

You will just have to cut it down to size and then do the repair accordingly.

Mrdgvb1 Social Media Links:
WEBSITE: https://www.swimmingpoollearning.com/
Google +: https://plus.google.com/b/107735343574734346096/
Blogger: https://poolmandave.blogspot.com/
Facebook: https://www.facebook.com/pages/Youtube-Mrdgvb1/381257741926763?ref=hl

If you found this video helpful, please visit my website, any donation is greatly appreciated.
WEBSITE: https://www.swimmingpoollearning.com/