8 Years manufacturer 5-PCS Hex Key Sets packaged by spring ring to Saudi Arabia Importers

Product page: https://mishimo.to/1U7rqkJ
Facebook: https://www.facebook.com/GoMishimoto
Twitter: https://www.Twitter.com/Mishimoto
Instagram: https://www.Instagram.com/Mishimoto

Mishimoto, the world leader in performance cooling products, shows you how to install the Mishimoto Silicone Hose Kit for the 2001-2005 Chevrolet Silverado/GMC Sierra w/ 6.6L Duramax engine!

The engineers at Mishimoto designed this silicone hose kit with multi-layered silicone that can withstand the heat and pressure that causes stock rubber hoses to fail. If you want to keep your Duramax cool, then you need the Mishimoto Silicone Hose Kit!

Model Number: MMHOSE-CHV-01D

2001-2005 Chevrolet/GMC Duramax 6.6L Silicone Coolant Hose Kit

PARTS LIST
(1) Mishimoto Upper Silicone Coolant Hose
(1) Mishimoto Lower Silicone Coolant Hose
(4) Mishimoto Stainless Steel T-Bolt Clamps

TOOLS NEEDED
8MM WRENCH
10MM WRENCH
15MM SOCKET
3/8” DRIVE RATCHET
LINEMAN’S PLIERS
PICK TOOL
COOLANT
FUNNEL

Disclaimer
• Please dispose of any liquids properly.
• Allow vehicle to cool completely prior to attempting installation.
• Mishimoto Performance (MP) is not responsible for any vehicle
damage or personal injury due to installation errors, misuse,
or removal of MP products.
• MP always suggests that a trained professional install all
MP products.
• Do not run the engine or drive the vehicle while overheating.
Serious damage may occur.
• Raise vehicle only on jack stands or on a vehicle lift.

INSTALLATION INSTRUCTIONS
01 | REMOVING THE OEM RADIATOR HOSES
1. Disconnect the negative terminal on both batteries.
2. Locate the drain plug on the base of the radiator and allow all
coolant to drain from the radiator.
3. Detach the upper radiator shroud by removing the eight pop clips.
4. Disconnect the upper coolant hose from the radiator.
5. Disconnect the upper coolant hose from the coolant outlet.
6. Remove the lower splash shield, which is secured with
five 15mm bolts.
7. Disconnect the lower radiator hose from the radiator, and
disconnect the lower coolant ancillary hoses.
8. Remove the lower coolant hose from the engine, and carefully
navigate the lower hose out from underneath the truck.

02 | INSTALLING THE MISHIMOTO SILICONE
RADIATOR HOSES
1. Connect the upper coolant hose to the radiator. Be sure to clamp
the new hoses down tightly with the provided clamps.
2. Connect the upper coolant hose to the engine.
3. Transfer the two retaining clips from the factory lower radiator
hose to the Mishimoto lower radiator hose. Use a screwdriver to
wedge into the side of the clip to loosen it.
4. Install the lower coolant hose and connect it to the engine and
radiator. Also connect the ancillary hoses to the proper
connections. Be sure to clamp down all connections tightly.
5. Reinstall the lower splash shield using five 15mm bolts.
6. Reconnect the negative battery terminal on both batteries.
7. Reinstall the upper radiator shroud and the eight pop clips that
secure it to the radiator support.
8. Refill the cooling system with a 50/50 mix of coolant and
distilled water.
9. Start the vehicle and set the heat to high to purge any air from the
cooling system. Allow the vehicle to reach operating temperature
and check for any leaks in the system.
10. You have now successfully installed the Mishimoto silicone
coolant hoses. Enjoy!

Download the guide here: https://lib.store.yahoo.net/lib/yhst-62631657248580/mmhose-chv-od1-installguide.pdf

DAWN Groove Joint Pliers Product Video