2016 New Style 4-PCS Small Tweezer Sets Factory in Brisbane
Short Description:
Product Detail
Product Tags
In order to give you convenience and enlarge our business, we also have inspectors in QC Team and assure you our best service and product for 2016 New Style 4-PCS Small Tweezer Sets Factory in Brisbane, We warmly welcome your participation based on mutual benefits in the near future.
Basic Information
■Model Number: RL-NZ003
Additional Information
■Material: Q195 Cold-rolled Steel
■Thickness: 0.8mm, 1.0mm, 1.2mm
■Surface Treatment: Chrome Plated
■Finish: Polished
■Package: Suction Card
■OEM: Acceptable
■HS Code: 8203200000
■Samples: For FREE
■Delivery Time: Always 30 working days depending on the order quantity
■Packing: By standard cartons
Attention
■Do not heat it.
■Do not take acid drugs with it.
■Keep it clean after using it.
Product Image
20503 Kit $229.95: https://amzn.com/B0002UNP6O
10105 Puller $99.95: – https://amzn.com/B000FN4NV4
10202 Installer $114.95: https://amzn.com/B000MEVQFM
70300 Pliers $14.95: https://amzn.com/B0002UNOTC
Product Details: https://www.tigertool.com/tools/?classification=automotive
Tiger Tool 10105 – U Joint Puller
U-Joint Puller designed to fit cars, light-duty trucks, and farm machinery.Fits u-joints with bearing cups 1.0″ to 1.25″ O.D”
- Eliminates dangerous vice and socket, or hammering methods.
- Removes sealed u-joint cups in minutes.
- Does not damage the driveshaft, yokes, joints, or bearing cups.
- Patented design provides the most effective mechanical advantage for disassembly.
- Heavy-duty construction.
- One piece unit (no assembly required). No bolts, no cables, and no adapters.
Tiger Tool 10202 Bearing Cup Installer:
The Tiger Bearing Cup Installer installs two bearing cups in one procedure. An encased magnet retains bearing cup #2 in place over the yoke assembly opposite the forcing bolt. Meanwhile, bearing cup #1 is maintained in place by the force of the rotating plunger at the end of the threaded bolt.
Both bearing cups are pressed simultaneously, freeing the mechanics hands to both; operate an air-wrench, and; maintain the position of the u-joint cross during the installation procedure.
Fits virtually all medium and light-duty universal joints.
The DSF is the main component in the kit or dado setup process. The unit has three ways of being held in place. First, it can be put in a bench vice and clamped in position. Second, using the two holes in the DSF, you can drill 3/8″ holes in your work surface and using the 3/8″ aligment pins can secure it to the top of you work surface. Third, you can use the MFT bushings to secure it to your MFT table. The hole spacing is designed to fit the MFT hole pattern. It should be noted that the second and third holding methods only keep the DSF from spinning. It can lift up out of the holes as the alignment pins only keep it from spinning when the user applies torque to the locking knob.
The DSF has a bronze 5/8″ arbor that can take up to a 15/16″ dado stack. The unit has a large diameter knob that is knurled to provide extra grip. This robust knob allows the user to put a lot of torque to squeeze the dado stack just like your table saw arbor nut would do.
Your dado stack most likely came with a chart that gave you a good indication of the combination of blades, chippers, and shims you are going to need to get to a certain width. This is a great start! use the Gap Gauge to get the exact thickness of your material and check that against this recommended combination. You will instantly be able to tell the fit of your dado. If the Gap Gauge doesn’t fit on the dado, then your dado stack is too large. You need to remove a shim or chipper. If there is slop in the fit and you are able to wiggle the Gap Gauge, then your dado stack is too thin/skinny. You need to add a shim or chipper that is the same thickness as the slop. It is that easy!
https://www.workshopaddict.com/tools/woodpeckers-onetime-tool-dado-setup-fixture-and-gap-gauges/
